Ordering

Mix and Match enables you to create a custom MikroMasch AFM probes box with quantities of 100, 150, 200, 250, 300, 350 or 400pcs. inside where you can mix different probe types in units of 50 pcs.

The more units of 50 AFM probes you order, the higher your discount will be from the 50 probes list prices of each variety ordered:

10% discount for 100pcs.
15% discount for 150pcs.
20% discount for 200pcs.
25% discount for 250pcs.
30% discount for 300pcs.
35% discount for 350pcs.
40% discount for 400pcs.

Go to Mix&Match Box page »

Order in a Mix&Match Box

Pay with

or by wire transfer

*All prices displayed are based on geolocation and therefore preliminary. For binding prices, please log on with your user data or create an account.

Other coatings:

Cobalt-Chromium coating, Backside Aluminum coating:
HQ:NSC18/Co-Cr/Al BS

Chromium-Gold coating:
HQ:NSC18/Cr-Au

No coating:
HQ:NSC18/No Al

Platinum coating:
HQ:NSC18/Pt

Backside Cromium-Gold coating:
HQ:NSC18/Cr-Au BS

Hard Diamond Like Carbon coating:
HQ:NSC18/Hard/ Al BS

More AFM probes with Backside Aluminum coating

Standard Tapping Mode AFM Probe:
HQ:NSC15/Al BS

Long Scanning, DLC Hardened Tapping Mode AFM Probe:
HQ:NSC15/Hard/Al BS

AFM Probe with 3 Different Tapping Mode Cantilevers:
HQ:NSC35/Al BS

AFM Probe with 3 Different Long Scanning, DLC Hardened Tapping Mode Cantilevers:
HQ:NSC35/Hard/Al BS

Magnetic Lift Mode and Force Modulation AFM Probe:
HQ:NSC18/Co-Cr/Al BS

AFM Probe with 3 Different Tapping Mode Cantilevers:
HQ:NSC36/Al BS

Magnetic AFM Probe with 3 Different Cantilevers:
HQ:NSC36/Co-Cr/Al BS

AFM Probe with 3 Different Long Scanning, DLC Hardened Tapping Mode Cantilevers:
HQ:NSC36/Hard/Al BS

AFM Probe with 4 Different Cantilevers for Various Applications:
HQ:XSC11/Al BS

AFM Probe with 4 Different Long Scanning, DLC Hardened Cantilevers for Various Applications:
HQ:XSC11/Hard/Al BS

AFM Probe with 3 Different Contact Mode Cantilevers:
HQ:CSC38/Al BS

Soft Tapping Mode AFM Probe:
HQ:NSC14/Al BS

Long Scanning, DLC Hardened, Soft Tapping Mode AFM Probe:
HQ:NSC14/Hard/Al BS

Standard Contact Mode AFM Probe:
HQ:CSC17/Al BS

Long Scanning, DLC Hardened Contact Mode AFM Probe:
HQ:CSC17/Hard/Al BS

Tipless AFM Probe with 3 Different Contact Mode Cantilevers:
HQ:NSC36/tipless/Al BS

Tipless AFM Probe with 3 Different Contact Mode Cantilevers:
HQ:CSC38/tipless/Al BS

Tipless AFM Probe with 3 Different Tapping Mode Cantilevers:
HQ:NSC35/tipless/Al BS

Tipless AFM Probe with 3 Different Tapping Mode Cantilevers:
HQ:CSC37/tipless/Al BS

AFM Probe with 3 Different Contact Mode Cantilevers:
HQ:CSC37/Al BS

Very Soft Tapping Mode and LFM AFM Probe:
HQ:NSC19/Al BS

Low Frequency Tapping Mode AFM Probe with Long Cantilever:
HQ:NSC16/Al BS

Low Frequency Long Scanning, DLC Hardened Tapping Mode AFM Probe with Long Cantilever:
HQ:NSC16/Hard/Al BS

HQ:NSC18/Hard/ Al BS

Hide List

HQ:NSC18/Al BS

Probe

HQ probe tip close-up

Typical radius of uncoated tip 8 nm
Typical spike radius 8 nm
Spike height
Resulting tip radius with the coating < 8 nm
Full tip cone angle* 40°
Total tip height 12 - 18 µm
Probe material n-type silicon
Probe bulk resistivity 0.01 - 0.025 Ohm*cm
Tip coating
Detector coating Aluminum

MikroMasch HQ Line Product Screencast on Series HQ:NSC18 and HQ:NSC19

MikroMasch HQ Line Product Screencast on Seies HQ:NSC18 and HQ:NSC19, presented by Dr. Penka Terziyska, Product Manager
www.spmtips.com

Subscribe to MikroMasch Youtube Channel

Cantilever

SEM image of the cantilever

Schematic drawing of the cantilever

Cantilever	Resonance Frequency, kHz			Force Constant, N/m			Length l ± 5, µm	Width w ± 3, µm	Thickness t ± 0.5, µm
Cantilever	min	typ	max	min	typ	max	Length l ± 5, µm	Width w ± 3, µm	Thickness t ± 0.5, µm
18 Series	60	75	90	1.2	2.8	5.5	225	27.5	3.0

*The full cone angle may be less than 40° at the last 200 nm of the tip end.

Ordering

Other coatings:

HQ:NSC18/Al BS

Probe

MikroMasch HQ Line Product Screencast on Series HQ:NSC18 and HQ:NSC19

Cantilever